Brother Troubleshooting: Error Codes and Jams

Last updated: August 21, 2026

Brother’s computerized machines have one advantage over an older mechanical model when something goes wrong: they tell you. A code appears on the little screen, the machine beeps, and it refuses to run. That is more helpful than it feels at the time, because the code narrows the problem down instead of leaving you guessing.

The catch is that the codes are terse and the manual is often in a drawer. Two of them account for most of what owners run into, and neither is a fault in any real sense. The rest of the Brother complaint list is the same threading, needle and bobbin trio that every brand has.

This article contains affiliate links. If you buy through them, we may earn a commission at no extra cost to you. Learn more.

Quick Answer

What do Brother error codes mean, and what causes the jams?

  • E1 means the presser foot is up. Brother’s support pages describe it as the start button or foot controller being pressed with the presser foot raised. Lower the foot and carry on.
  • E6 is a motor safety stop, and Brother describes it as a motor overload. It usually means thread is tangled in the bobbin area.
  • A jam under the fabric is a thread path problem, not a bobbin tension problem. Rethread the top with the foot raised.
  • Codes beginning with F point at something inside the machine. Look the code up for your model on Brother’s support site and take it in rather than opening it.

Bottom line: E1 and E6 are the machine protecting itself. Almost everything else is threading, needle or bobbin.


Reading the Codes

Brother uses short alphanumeric codes on the display of its computerized machines, and each one maps to a defined condition rather than a general fault. The two that come up most in owner reports are E1 and E6, and both of them are the machine refusing to run for a reason you can clear at the table in under a minute.

Codes vary between model families, so the definitive list is the one in your manual or on Brother’s support site for your model number. What follows is the general shape of the system and the two codes almost every owner meets.

E1: the Presser Foot Is Up

Brother’s support material describes E1 as the condition where the start and stop button or the foot controller is pressed while the presser foot is raised. Lower the presser foot lever and the machine runs. That is the whole thing, and it is by far the most common code people search for.


E6 and Motor Overload

Brother describes E6 as a motor overload condition. In practice it appears when something has stopped the mechanism turning freely: thread wound around the bobbin race, fabric jammed down into the needle plate, or a needle striking the plate. The machine cuts the motor rather than fighting it, which is exactly what you want it to do.

Switch the machine off at the power switch and look under the throat plate. Remove the bobbin, clear any thread that has wound around the race, and check whether the needle is bent or broken. Turn the handwheel gently by hand toward you: if it does not move freely, do not switch the machine back on until you have found out why.

Clearing a Jam Without Making It Worse

Cut the threads rather than pulling the fabric, raise the presser foot, and ease the work out backward. Pulling forward against a jam bends the needle and can drag thread further into the hook. Fit a new needle afterward as a matter of course, because a needle involved in a jam is bent whether or not it looks it.


The Thread Nest Under the Fabric

The most reported non code Brother complaint is a mass of loose thread on the underside of the fabric, usually at the start of a seam. It looks like a bobbin fault and it almost never is one. The top thread has failed to come under tension, and the excess is dragged down through the needle hole.

Rethread the top completely with the presser foot raised, because the tension discs only open when the foot goes up. Then hold both thread tails behind the foot for the first few stitches when you start a seam, which is what stops the top thread being pulled down before the stitch has formed. Our article on thread nests covers the sequence in full, and the Brother XM2701 review covers the entry machine this catches most often.


Skipped Stitches and the Needle

Skipped stitches on a Brother follow the same rule as on any machine. Fit a new needle before you change anything else, push it all the way up into the clamp until it stops, and set the flat of the shank toward the back. A needle that is bent, blunt or sitting slightly low misses the hook and produces a skipped stitch that looks like a machine fault.

Then match the point to the fabric. Universal needles push between the yarns of a knit rather than piercing them, which is why jersey and stretch fabrics skip on a needle that works perfectly on cotton. A ballpoint or jersey needle fixes it, and our guide to sewing machine needles covers sizes and points together.

The Automatic Needle Threader

Brother’s automatic needle threader only works with the needle at its highest position, so raise the needle fully before you use it and do not force the lever if it resists. A bent threader hook is a common repair, and it comes from using it out of position rather than from wear.


Bobbin Problems on a Drop In System

Most current Brother home machines use a drop in bobbin under a clear cover, which is convenient and has two specific failure modes. The bobbin can be dropped in turning the wrong way, and the thread can be laid across the top instead of being pulled through the slot in the case, which leaves it with no bobbin tension at all.

The diagram printed next to the bobbin area shows the correct direction, and it is worth looking at rather than trusting memory. Pull the thread through the guide slot until you feel a light drag, close the cover fully, and check the machine actually picks up the bobbin thread before you start on the real fabric.

Which Bobbin the Machine Takes

Brother sells bobbins under its own part numbers, and the manual lists the correct one for your model. Bobbins from another brand or another machine can drop in and look right while sitting a fraction too high or too low, which causes tension trouble that no dial corrects. Our guide to which bobbin fits my machine covers checking rather than guessing.


The Codes and Complaints in One Place

The table below collects the two codes Brother documents on its support pages alongside the two complaints owners raise most, with the first thing to do in each case.

What you seeWhat it meansFirst moveIf that fails
E1 on the displayPresser foot raised when startingLower the presser foot leverCheck the foot lever is fully down
E6 on the displayMotor overload, usually a jamPower off, clear thread from the raceHandwheel stiff, take it in
Thread nest underneathTop thread not in the tension discsRethread with the foot raisedReseat the bobbin, clean the race
Skipped stitchesNeedle bent, low, or wrong pointNew needle, fully seated, flat to backBallpoint for knits, then a technician
An F codeAn internal faultLook it up for your model on Brother supportTake it to a service center

For model level differences rather than symptoms, the Brother hub collects the lines, and Brother model numbers explained decodes what the letters and digits mean.


Keeping It Out of Trouble

Two habits prevent most of what is in this article. Clean under the throat plate every few projects, because lint packs around the hook faster than anyone expects and it causes noise, drag and tension trouble at once. And change the needle far more often than feels necessary, because a needle costs almost nothing and a bent one causes almost everything.

Brother’s manuals set out the cleaning steps for each model and are worth following rather than improvising. Do not blow into the machine, and do not oil anything your manual does not identify as an oiling point. Our ten minute maintenance routine covers the general version.

When It Goes to a Technician

An F code, a stiff handwheel, a burning smell, a broken needle threader or a machine that has taken a hard knock all belong with a service center rather than with a screwdriver at the dining table. Brother has an authorized service network and most towns have an independent technician who is quicker. Read when to take it to a repair shop for what to say when you get there.


Frequently Asked Questions

What does E1 mean on a Brother sewing machine? Brother’s support material describes E1 as the start and stop button or foot controller being pressed while the presser foot is raised. Lower the presser foot and the machine runs. It is not a fault.

What does E6 mean? Brother describes E6 as a motor overload. In practice it means the mechanism cannot turn freely, usually because thread has wound around the bobbin race or fabric has jammed. Power off, clear it, and check the handwheel turns freely before restarting.

Why does my Brother keep making a nest of thread underneath? The top thread is not seated in the tension discs. Rethread from the spool with the presser foot raised, and hold both thread tails behind the foot for the first few stitches of a seam.

My automatic needle threader has stopped working. Can I fix it? Check first that the needle is raised to its highest position, because the threader only works there. If the small hook is bent, that is a repair rather than an adjustment, and forcing it makes it worse.

Can I use any bobbin in a Brother machine? No. Use the bobbin the manual specifies for your model. Bobbins that look identical can differ enough in height or diameter to sit at the wrong depth, which causes tension problems that no adjustment will fix.


The Bottom Line

Two Brother codes cover most of what owners meet, and Brother documents both: E1 means the presser foot is raised, and E6 is a motor overload that almost always means a jam in the bobbin area. Everything else on the complaint list is the universal trio, a top thread threaded with the foot down, a needle that is bent or the wrong point, and a bobbin in backward or from the wrong class. Clean under the plate regularly, change needles often, and send F codes to a service center. Read next: the Brother hub, the Brother XM2701 review, and thread nests under the fabric.